Beyond Better
Bravura88
Member
Find latest postsMini Statistics
- Join Date
- 11-06-2011
- Last Activity
- 05-05-2013 02:35 PM
Recent Visitors
This page has had 492 visits
- Tab Content
- Bravura88's Activity
- About Me
- Friends
-
Older Activity
-
05-02-2013, 01:17 PMYes, I just pulled engine and interior then gave him the boat. This guy has a lot of experience with these boats so I would have expected him to put...28 replies | 313 view(s) -
05-02-2013, 01:00 PMThe pic that I posted, if you can see it is with the reducer on. With that on there is only 2inches left between the reducer and pipe. You can also...28 replies | 313 view(s)
-
05-02-2013, 12:54 PM28 replies | 313 view(s)
-
05-02-2013, 12:29 PMThink I found out lets see if the pic posts?28 replies | 313 view(s)
-
05-02-2013, 12:23 PMHey guys, went out this morning and no luck with the hose. I would like to post a pic so you guys can take a look but am having trouble. Does...28 replies | 313 view(s)
-
04-29-2013, 09:22 PMSalty was thinking about that ( maybe even throwing them in the oven for a bit (haha)! Soapy water isn't a bad idea either. Pics will have to wait...28 replies | 313 view(s)
-
04-29-2013, 07:52 PMSyber as bad as it sounds yours look a little more lined up then mine. I'm am going to do the same exact way you did and try one more time. If not...28 replies | 313 view(s)
-
04-29-2013, 06:32 PMSalty I think that is my problem! I will try and post some pics and see what you guys think but your pipe is higher than mine by a few inches and...28 replies | 313 view(s)
-
04-29-2013, 06:00 PMThx for the replies guys! Its not so much that I'm worried about the hose bending it that with only the 6-7 inches it has to make the bend is not...28 replies | 313 view(s)
-
04-29-2013, 03:52 PMThe engine is aligned with the shaft and I would guess the only spot it could be? The problem is I had to completely change the mounts to get it to...28 replies | 313 view(s)
-
04-29-2013, 02:33 PMThx. Do you or any of the other guys know if that is standard to be straight from risers to pipes like yours? Or where there some that had bends in...28 replies | 313 view(s)
-
04-29-2013, 02:14 PMIt does salty thx. You do have the 454 in your Salt?28 replies | 313 view(s)
-
04-29-2013, 02:02 PMSalty thx, I should have been more specific about what part my fault! I actually need the set up from the tip of the exhaust manifold the rubber...28 replies | 313 view(s)
-
04-29-2013, 12:53 PMHi guys, was wondering if the Saltare owners could post a few pics from the side of the exhaust set up. Just need it from the manifold down to...28 replies | 313 view(s)
-
04-23-2013, 06:09 PMNo doubt its tight. I was running into the same problem with the oil drain plug hitting the hull! Thx for the replays guys makes me feel better...7 replies | 157 view(s)
-
04-21-2013, 05:56 PMThanks for the reply Salty! Got her bolted down and aligned today and I kept doing the cardboard test (piece of a package box to slide between pan &...7 replies | 157 view(s)
-
04-20-2013, 10:07 PMHad stringers and floor redone and now putting engine back in. How close to the hull does the pan sit to the hull when in? I don't think I have...7 replies | 157 view(s)
About Bravura88
Basic Information
Statistics
Total Posts
- Total Posts
- 43
- Posts Per Day
- 0.08
General Information
- Last Activity
- 05-05-2013 02:35 PM
- Join Date
- 11-06-2011
- Referrals
- 0
© 2013 Supra Boats | All Rights Reserved